How to judge whether there is a problem with the linear guide rail and slide? A key part of the linear motor of the guide rail and slide, the equipment can not run without cars, but in the process of equipment operation, there are many factors that cause damage to our motor guide slide, then we need to check and judge its quality in time, and do preventive work as early as possible. Dongguan Liaobu iron and steel Sheng Machinery Parts Co., Ltd., as an enterprise specializing in selling sliders and guide rails, let's discuss the problems between them:

　　直線電機發生報警，通常超過100H，內部清洗后，復位仍報警。這一現象的發生說明直線電機存在問題。此時我們需要注意電機的滑塊和導軌，進一步檢查滑塊和導軌是否有問題。2. 直線電機運行時抖動，溫度較高。這種現象通常發生在臺式極電機中，通過我們的停電檢查可以確定是否滑軌的原因。

　　Linear motor alarm occurs, usually more than 100h, after internal cleaning, reset still alarm. This phenomenon shows that there are problems in linear motor. At this time, we need to pay attention to the slider and guide rail of the motor, and further check whether there is any problem with the slider and guide rail. 2. When the linear motor is running, it vibrates and the temperature is high. This phenomenon usually occurs in the desk pole motor. Through our power failure check, we can determine the cause of the slide.

　　直線電機一啟動就報警，或者運行一段時間后報警，復位后再次報警。在設備參數正常情況下，該情況表明直線電機的滑塊或?qū)к壱呀?jīng)磨損，需要及時停機檢查。設備停機或維修時的判斷;設備停機或維修時的判斷;設備停機或維修時的判斷。當新的滑塊進入指南時，您應該左右按滑塊。直到新的滑塊上的指南順利和容易沒有阻力。6. 安裝和恢復操作后電機導軌上的滑塊,滑塊的位置移動到電動機轉子上的滑塊槽的位置,然后瓦2層布電機定子,厚度是一樣的滑塊的高度,然后輕輕調整電動機的轉子和滑塊,慢慢落下來直到它們掉下來!

　　As soon as the linear motor starts, it will alarm, or it will alarm after a period of operation, and it will alarm again after reset. Under the normal condition of equipment parameters, this condition indicates that the sliding block or guide rail of linear motor has been worn and needs to be stopped and checked in time. Judgment of equipment shutdown or repair; judgment of equipment shutdown or repair; judgment of equipment shutdown or repair. When the new slider enters the guide, you should press the slider left and right. Until the new slider on the guide goes smoothly and easily without resistance. 6. After the installation and recovery of the slider on the motor guide rail, the position of the slider moves to the position of the slider slot on the motor rotor, and then the stator of the motor is laid with two layers of tiles, the thickness of which is the same as the height of the slider, and then slightly adjust the motor rotor and the slider, and slowly fall down until they fall down!

　　以上是導軌絲杠制造商小編為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://www.idczc.com

　　The above is the related content introduced by the manufacturer of guide screw. If you want to know more, please visit the website: http://www.idczc.com